任务4 加键槽轴零件图样的识读 29 任务引入与分析 29 相关知识 29 一、三视图的概念和形成(Concept and forming of the three views) 29 二、三视图的投影规律(Projective rules of the three views) 31 三、三视图与物体方位的对应关系(Positional corresponding relationship of the three views and objects) 31 四、三视图的作图方法(Constructing methods of the three views) 32 任务实施 33 知识拓展——表面结构(Surface texture) 35
任务5 加螺纹轴零件图样的绘制 39 任务引入与分析 39 相关知识 40 一、螺纹的形成和基本要素(Formation and basic elements of threads) 40 二、螺纹的规定画法(Conventional representation of threads) 43 三、螺纹的规定标注(Conventional designation of threads) 44 任务实施 46 知识拓展——轴套类零件的结构与加工方法举例 47
任务6 加螺纹轴零件图样的识读 50 任务引入与分析 50 相关知识 51 一、极限与配合的基本概念(Basic concept of limits and fits) 51 二、极限与配合(Limits and fits) 54 任务实施 56 知识拓展——轴套类零件的视图与尺寸分析 57
任务1 拨叉零件图样的绘制 121 任务引入与分析 121 相关知识 122 一、叉架类零件的结构分析(Structural analysis of the parts of the fork- frame group) 122 二、叉架类零件常用的表达方式(Commonly used expression of the parts of the fork-frame group) 122 任务实施 136
任务2 拨叉零件图样的识读 137 任务引入与分析 137 相关知识 137 一、认识叉架(Cognition the parts of the fork-frame group) 137 二、简化画法(Simplified representation) 138 三、局部放大图(Drawing of partial enlargement) 142 任务实施 143 知识拓展——第三角画法简介(Introduction of third-angle projection) 144
模块4 箱体类零件图样的绘制与识读 147
任务1 泵体零件图样的绘制 147 任务引入与分析 147 相关知识 148 一、箱体类零件(The parts of the case-housing group) 148 二、箱体类零件图上的技术要求(Technical requirements of detail drawing of case-housing group parts ) 148 三、几何误差(Geometric tolerances) 149 四、零件图的尺寸标注(Dimensioning of detail drawing) 154 任务实施 159
任务1 齿轮油泵标准件和常用件的绘制 167 任务引入与分析 167 相关知识 167 一、螺纹连接画法(The methods of the threaded connection) 167 二、常用螺纹紧固件及其连接画法(The commonly used threaded fasteners and drawing methods of connection) 168 三、啮合齿轮(Mating gears) 173 四、键连接、销连接(Key joints and Pin joints) 174 五、滚动轴承(Rolling bearings) 176 任务实施 179 知识拓展——弹簧 180
任务2 支架装配图的绘制 182 任务引入与分析 182 相关知识 183 一、装配图的作用和内容(Function and content of assembly drawing) 183 二、装配图的表达方法(Representation of assembly drawing) 185 三、装配图的尺寸标注(The dimensions of an assembly drawing) 187 四、装配图中零件的序号和明细栏(Part sequence number of parts and item block of assembly drawing) 188 五、装配图的技术要求(Technical requirements of assembly drawing) 189 任务实施 190
任务4 由装配图拆画零件图 201 任务引入与分析 201 相关知识 201 一、认真阅读装配图(Carefully read the assembly drawing) 202 二、确定零件的表达方案(Determine the parts of the expression method) 202 三、零件图的尺寸标注(Dimensioning of detail drawing) 203 四、零件图的技术要求(Technical requirements of detail drawing) 204 任务实施 204
附录 207 1.键(Key) 207 2.销(Pin) 210 3.螺纹(Screw Threads) 212 4.常用螺纹紧固件(Commonly used Screw fasteners) 216 5.极限与配合(Limits and Fits) 223 6.滚动轴承(Rolling Bearings)(摘自GB/T 276-1994、GB/T 297-1994和GB/T 301-1995) 231 7.中心孔(Center Hole)(摘自GB/T145-2001) 232 8.中心孔表示法(Expression of Center Hole)(摘自GB/T4459.5-1999) 232 9.倒圆与倒角(Chamfers and Fillet)(摘自GB/T 6403.4-2008) 233 10.其他(Others) 233
以下为对购买帮助不大的评价