互换性与测量技术
正版保障 假一赔十 可开发票
￥ 58.08 6.6折 ￥ 88 全新
库存3件
广东广州
认证卖家担保交易快速发货售后保障
作者郭玉琴，刘晨曦，王宏宇编
出版社化学工业出版社
ISBN9787122426260
出版时间2023-07
装帧平装
开本16开
定价88元
货号12805553
上书时间2024-11-04
商品详情
- 品相描述：全新
- 商品描述
-
作者简介
无
目录
Chapter 1 Introduction 001
1.1 Interchangeability and Tolerance 002
1.2 Standards and Standardization 004
1.3 Series of Preferred Numbers 005
1.4 Overview of Geometric Parameters Detection 007
1.5 Properties and Objectives of the Course 009
Questions and Exercises 010
Definitions for Key Terms 011
Chapter 2 Limits and Fits of Shaft and Hole 012
2.1 Introduction 013
2.2 Basic Terms and Definitions 014
2.2.1 Terms and Definitions of Size 014
2.2.2 Terms and Definitions of Deviation and Tolerance 015
2.2.3 Terms and Definitions of Fit 018
2.2.4 Fit System 020
2.3 Limits and Fits of Common Size 021
2.3.1 Standard Tolerance Series 021
2.3.2 Fundamental Deviation Series 023
2.3.3 Indication of the Limits and Fits on Engineering Drawing 031
2.3.4 Recommended Tolerance Zones of Hole/Shaft and Fits 031
2.4 Limits and Fits of Large Size Hole/Shaft 034
2.5 General Tolerance for Linear Sizes without Individual Tolerance Indication 036
2.6 Size Accuracy Design 037
2.6.1 Basic Principles and Methods 037
2.6.2 Selection of Fit System 037
2.6.3 Selection of Standard Tolerance Grade 040
2.6.4 Selection of Fit Type 041
2.6.5 Example for Size Accuracy Design 046
Project Ⅰ：Size Measurement 048
Questions and Exercises 049
Definitions for Key Terms 051
Chapter 3 Geometrical Tolerance and Error Measurement 053
3.1 Introduction 054
3.2 Geometrical Features and Characteristics of Geometrical Tolerances 054
3.2.1 Geometrical Features and Their Classifications 054
3.2.2 Characteristics and Symbols of Geometrical Tolerances 056
3.3 Indication of Geometrical Tolerance on Engineering Drawing 057
3.3.1 Geometrical Tolerance Frame and Datum Symbol 057
3.3.2 Indication of Measured Features 058
3.3.3 Indication of Datum 060
3.3.4 Simplified Indication Methods 061
3.4 Geometrical Tolerance Zone 062
3.4.1 Fundamental Characteristics of Geometrical Tolerance Zone 062
3.4.2 Datum 063
3.4.3 Form Tolerance Zone 066
3.4.4 Orientation Tolerance Zone 068
3.4.5 Location Tolerance Zone 073
3.4.6 Profile Tolerance Zone 077
3.4.7 Runout Tolerance Zone 079
3.5 Tolerance Principles 081
3.5.1 Terms and Definitions about Tolerance Principle 082
3.5.2 Independence Principle 085
3.5.3 Envelope Requirement 087
3.5.4 Maximum Material Requirement 089
3.5.5 Least Material Requirement 096
3.6 Geometrical Accuracy Design 099
3.6.1 Selection of Geometrical Tolerance Characteristics and Datum 100
3.6.2 Selection of Tolerance Principle 101
3.6.3 Selection of Geometrical Tolerance Value 103
3.6.4 Example for Geometrical Accuracy Design 107
ProjectⅡ：Measurement of Geometrical Deviations 109
Questions and Exercises 110
Definitions for Key Terms 113
Chapter 4 Surface Roughness and Its Measurement 116
4.1 Introduction 117
4.1.1 Definition of Surface Roughness Profile 117
4.1.2 Effect of Surface Roughness on Performance and Fit Quality 118
4.2 Evaluation Parameters of Surface Roughness 120
4.2.1 Basic Terms and Definitions 120
4.2.2 Definitions of Evaluation Parameters 122
4.3 Selection of Surface Roughness Parameter and Its Value 124
4.4 Indications of Surface Texture Requirements on Engineering Drawing 128
4.5 Measurement of Surface Roughness 133
Project Ⅲ：Measurement of Maximum Height of Profile 138
Questions and Exercises 138
Definitions for Key Terms 139
Chapter 5 Tolerance and Measurement of Involute Cylindrical Gear 141
5.1 Introduction 142
5.2 Operating Requirements for Gear Drive 143
5.3 Main Influence Factors on Gear Drive Error 144
5.4 Evaluation Parameters of Involute Cylindrical Gear and Their Measurement 149
5.4.1 Evaluation Parameters of Transfer Motion Accuracy and Their Measurement 149
5.4.2 Evaluation Parameters of Drive Stability and Their Measurement 156
5.4.3 Evaluation Parameters of Load Distribution Uniformity and Their Measurement 159
5.4.4 Evaluation Parameters of Backlash and Their Measurement 162
5.5 Accuracy Design of Involute Cylindrical Gear 165
5.5.1 Accuracy Grades and Indication on Engineering Drawing 165
5.5.2 Limit Deviations of Backlash Parameters 166
5.5.3 Tolerance of Gear Blank 169
5.5.4 Tolerance of Gear Pair 170
Project Ⅳ：Measurement of Involute Cylindrical Gear 172
Questions and Exercises 173
Definitions for Key Terms 174
Chapter 6 Tolerance and Measurement of Typical Parts 176
6.1 Tolerance and Fit of Rolling Bearing 177
6.1.1 Tolerance Grades of Rolling Bearing and Application 177
6.1.2 Tolerance Zone and Characteristic of Rolling Bearing 178
6.1.3 Rolling Bearing Fit 179
6.2 Tolerance，Fit and Measurement of Key and Spline 184
6.2.1 Tolerance，Fit and Measurement of Flat Key Connection 184
6.2.2 Tolerance，Fit and Measurement of Rectangle Spline Connection 189
6.3 Tolerance，Fit and Measurement of Common Thread 193
6.3.1 Basic Geometrical Parameters of Common Thread 194
6.3.2 Tolerance and Fit of Common Thread 194
6.3.3 Measurement of Common Thread 198
6.4 Tolerance，Fit and Measurement of Cone 199
6.4.1 Basic Terms of Cone Tolerance and Fit 200
6.4.2 Cone Tolerance Features and Their Selection 202
6.4.3 Measurement of Cone 203
Questions and Exercises 204
Definitions for Key Terms 205
References 207
内容摘要
本书根据高等教育国际化相关要求，为满足“互换性与测量技术”课程双语教学和留学生英文授课需要而编写，系统介绍了互换性与测量技术的基本概念、相关标准的构成、基本内容及具体规定，并提供在线课程。同时，每章均给出教学目标、综合性教学案例剖析，并附有知识脉络图、思考/练习题、重点术语及定义。本书可作为高等学校机械类相关专业双语教学或全英文授课的教材或参考书，也可供相关工程技术人员参考。
This book is compliled to meet the needs of bilingual and English teaching of the “Interchangeability and Measurement Technology”course for international students，according to the requirements of the internationalization of higher education.In this book，the fundamental concepts of interchangeability and measurement technology，as well as the basic content and specific regulations of the relevant standards are systematically introduced.And the corresponding online open course is also provided.Meanwhile，teaching objectives，analysis of comprehensive teaching cases，knowledge frame diagram，questions and exercises，and definitions for key terms are given in each chapter.This book can simultaneously serve as the textbook of bilingual and English teaching for mechanical related majors as well as reference book for concerned engineers and technicians.
精彩内容
相关推荐
— 没有更多了 —
以下为对购买帮助不大的评价